File manager - Edit - /home/newsbmcs.com/public_html/static/img/logo/microchip.tar
Back
Kconfig 0000644 00000001022 15030353011 0006031 0 ustar 00 # SPDX-License-Identifier: GPL-2.0 config WLAN_VENDOR_MICROCHIP bool "Microchip devices" default y help If you have a wireless card belonging to this class, say Y. Note that the answer to this question doesn't directly affect the kernel: saying N will just cause the configurator to skip all the questions about these cards. If you say Y, you will be asked for your specific card in the following questions. if WLAN_VENDOR_MICROCHIP source "drivers/net/wireless/microchip/wilc1000/Kconfig" endif # WLAN_VENDOR_MICROCHIP wilc1000/Kconfig 0000644 00000003703 15030353011 0007300 0 ustar 00 # SPDX-License-Identifier: GPL-2.0 config WILC1000 tristate help Add support for the Atmel WILC1000 802.11 b/g/n SoC. This provides Wi-FI over an SDIO or SPI interface, and is usually found in IoT devices. This module only support IEEE 802.11n WiFi. config WILC1000_SDIO tristate "Atmel WILC1000 SDIO (WiFi only)" depends on CFG80211 && INET && MMC select WILC1000 help This module adds support for the SDIO interface of adapters using WILC1000 chipset. The Atmel WILC1000 SDIO is a full speed interface. It meets SDIO card specification version 2.0. The interface supports the 1-bit/4-bit SD transfer mode at the clock range of 0-50 MHz. The host can use this interface to read and write from any register within the chip as well as configure the WILC1000 for data DMA. To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select this if your platform is using the SDIO bus. config WILC1000_SPI tristate "Atmel WILC1000 SPI (WiFi only)" depends on CFG80211 && INET && SPI select WILC1000 select CRC7 select CRC_ITU_T help This module adds support for the SPI interface of adapters using WILC1000 chipset. The Atmel WILC1000 has a Serial Peripheral Interface (SPI) that operates as a SPI slave. This SPI interface can be used for control and for serial I/O of 802.11 data. The SPI is a full-duplex slave synchronous serial interface that is available immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to VDDIO. Select this if your platform is using the SPI bus. config WILC1000_HW_OOB_INTR bool "WILC1000 out of band interrupt" depends on WILC1000_SDIO help This option enables out-of-band interrupt support for the WILC1000 chipset. This OOB interrupt is intended to provide a faster interrupt mechanism for SDIO host controllers that don't support SDIO interrupt. Select this option If the SDIO host controller in your platform doesn't support SDIO time division interrupt. wilc1000/Makefile 0000644 00000000447 15030353011 0007437 0 ustar 00 # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_WILC1000) += wilc1000.o wilc1000-objs := cfg80211.o netdev.o mon.o \ hif.o wlan_cfg.o wlan.o obj-$(CONFIG_WILC1000_SDIO) += wilc1000-sdio.o wilc1000-sdio-objs += sdio.o obj-$(CONFIG_WILC1000_SPI) += wilc1000-spi.o wilc1000-spi-objs += spi.o Makefile 0000644 00000000200 15030353011 0006163 0 ustar 00 # SPDX-License-Identifier: GPL-2.0-only obj-$(CONFIG_COMMON_CLK_PIC32) += clk-core.o obj-$(CONFIG_PIC32MZDA) += clk-pic32mzda.o ksz9477_spi.ko 0000644 00000043641 15030530622 0007120 0 ustar 00 ELF >